Our Guarantee:

We provide you a 100% money-back guarantee for 30 days so long as the product is returned in "like new" condition and is a stock size item. If the product is a custom built, we will do what we can to remedy any issue that arises up to and including modifying the product to accommodate your need.

All stock size items have a 1 year warranty against defects in materials and workmanship. Performer Hay Tarps have a pro-rated three year warranty against defects in materials and workmanship and UV damage.

New and replacement building covers also come with an extended warranty. Please contact us for the specifics on each warranty by calling 800-346-7744. We can then provide you a faxed copy.

Need a Line of Credit? Access to exclusive financing. No annual fee.

Need a liner for your pond, containment pit, lagoon or lake? We are the one stop online store for all your Liner needs. Our manufacturing process allows us to manufacture large one piece liners up to 150,000 sq.ft., which can help reduce your installation time and cost.

Liner material thickness is measured in mils or 1000ths of an inch. Inland Tarp & Liner carries a wide range of liner materials to fit almost any application. Our standard liner materials are a 12mil, 16mil, 20mil, 24mil and 30mil woven PE (polyethylene) material that is black on both sides. We also carry a 30mil and 40mil LLDPE (linear low-density polyethylene) and a geomembrane material in a 8 ounce Felt.

Coated Woven Polyethylene (CWPE) is made from woven HDPE tapes known as “base fabric” or “scrim” which provide high tear strengths and puncture resistance. The HDPE scrim is coated on both sides with LDPE to provide flexible barriers to contain liquid. Standard products are three ply - that is 1 scrim layer with coating on top and bottom.

Property	Reading	Unit	Test Method
Thickness nominal	24	mils	ASTM D 1777*
Mass per Unit Area	11.4	oz/yd. ²	ASTM D 751
Grab Tensile: Warp Weft	297 308	lbs lbs	ASTM D 751
Tongue Tear Resistance: Warp Weft	59 59	lbs lbs	ASTM D 751
Hydrostatic Resistance	227	psi	ASTM D 751
Mullen Burst Strength	525	psi	ASTM D 3786
Puncture Resistance	137	lbs	ASTM D 4833
Color	Black		Observed

UV Accelerated Weathering
More than 90% strength retained after 2,000 hours exposure

*ASTM D1777 Option 1.

All values are +/- 10% and are not intended as limiting specifications.

1.) For accurate measurements measure your ponds widest width, longest length and deepest depth (in feet). The diagram above shows you how to correctly measure your pond.

2.) Every pond should have an anchor trench to prevent the liner from sliding down the slope and into the pond. We recommend no less than a 12" wide and 12" deep anchor trench. The deeper the pond the larger the anchor trench.

3.) All liners have some degree of expansion and contraction as the ambient temperature changes from summer to winter and back to summer. Therefore, liners must be installed with some slack ripples. A liner that is installed tight without these slack ripples can trampoline in the base and corners- in turn creating a liner failure. A liner installed in a colder climate or at a cooler time of day will require more slack ripples. We recommend adding 1' to 3' to each side of your final measurement to accomodate for this requirement.

Advantages with buying from ITL

O&G Liner Experience in Multiple Plays . . . Containment 

Rapid Turnaround & Delivery & Customer Service

Factory Tested

Coated Woven Reinforced Liner Products

Custom Fabrication . . . single piece liners and single felt panels

O&G Industry Pulse for Changing Liner Needs . . . R&D w/ Solutions

 

Liners, Pond Liners, Pit Liners, Impoundment Liners, Containment Liner, Secondary Containment Liner, Frac Tank Liners, Spill Containment Liners, Tank Liners, Geomembrane, Geomembrane Containment Liners

Customer Reviews