20' X 20' 24 Mil Coated Woven Polyethylene (CWPE) Liner Black/Black
Our Guarantee:[X] Close
We provide you a 100% money-back guarantee for 30 days so long as the product is returned in "like new" condition and is a stock size item. If the product is a custom built, we will do what we can to remedy any issue that arises up to and including modifying the product to accommodate your need.
All stock size items have a 1 year warranty against defects in materials and workmanship. Performer Hay Tarps have a pro-rated three year warranty against defects in materials and workmanship and UV damage.
New and replacement building covers also come with an extended warranty. Please contact us for the specifics on each warranty by calling 800-346-7744. We can then provide you a faxed copy.
ITL® 24 mil CWPE™ LinersSKU: LNR20X2024MILBB
Fabricated To Ship Within 1 To 4 Business Days
Fabricated and shipped from Moses Lake, WA or Fostoria, OH. Orders are prioritized by when they are received.
This product weighs 32.00 lbs.
ITL® Technical Data
Find Technical Data Sheets, Installation Guides & Warranty information at the ITL Technical Data Center.
Size & Material
Selected Color: Black/Black
100% Satisfaction Guaranteed!*
Need a liner for your pond, containment pit, lagoon or lake? We are the one stop online store for all your Liner needs. Our manufacturing process allows us to manufacture large one piece liners up to 150,000 sq.ft., which can help reduce your installation time and cost.
Liner material thickness is measured in mils or 1000ths of an inch. Inland Tarp & Liner carries a wide range of liner materials to fit almost any application. Our standard liner materials are a 12mil, 16mil, 20mil, 24mil and 30mil woven PE (polyethylene) material that is black on both sides. We also carry a 30mil and 40mil LLDPE (linear low-density polyethylene) and a geomembrane material in a 8 ounce Felt.
|Coated Woven Polyethylene (CWPE) is made from woven HDPE tapes known as “base fabric” or “scrim” which provide high tear strengths and puncture resistance. The HDPE scrim is coated on both sides with LDPE to provide flexible barriers to contain liquid.
Standard products are three ply - that is 1 scrim layer with coating on top and bottom.
|Thickness nominal||24||mils||ASTM D 1777*|
|Mass per Unit Area||11.4||oz/yd. ²||ASTM D 751|
|ASTM D 751|
|Tongue Tear Resistance:
|ASTM D 751|
|Hydrostatic Resistance||227||psi||ASTM D 751|
|Mullen Burst Strength||525||psi||ASTM D 3786|
|Puncture Resistance||137||lbs||ASTM D 4833|
More than 90% strength retained after 2,000 hours exposure
*ASTM D1777 Option 1.
All values are +/- 10% and are not intended as limiting specifications.
1.) For accurate measurements measure your ponds widest width, longest length and deepest depth (in feet). The diagram above shows you how to correctly measure your pond.
2.) Every pond should have an anchor trench to prevent the liner from sliding down the slope and into the pond. We recommend no less than a 12" wide and 12" deep anchor trench. The deeper the pond the larger the anchor trench.
3.) All liners have some degree of expansion and contraction as the ambient temperature changes from summer to winter and back to summer. Therefore, liners must be installed with some slack ripples. A liner that is installed tight without these slack ripples can trampoline in the base and corners- in turn creating a liner failure. A liner installed in a colder climate or at a cooler time of day will require more slack ripples. We recommend adding 1' to 3' to each side of your final measurement to accomodate for this requirement.
Advantages with buying from ITL
O&G Liner Experience in Multiple Plays . . . Containment
Rapid Turnaround & Delivery & Customer Service
Coated Woven Reinforced Liner Products
Custom Fabrication . . . single piece liners and single felt panels
O&G Industry Pulse for Changing Liner Needs . . . R&D w/ Solutions
How We Measure Up . . . ITL Coated-Woven (CWPE) Vs. Leading LLDPE
UV Accelerated Weathering. More than 90% strength retained after 2,000 hours exposure.
*ASTM D1777 Option 1. All values are +/- 10% and are not intended as limiting specifications.
DISCLAIMER: The information contained herein is provided for reference purposes only and is not intended as a warranty or guarantee. Final determination of suitability for application is the sole responsibility of the user. These values are based on testing results from past fabric runs. Each production run varies in final results. If a certain specified value is required, please inform ITL in advance and we can provide current testing results. Last updated November 22, 2011.